Product Details
|
Fulflo? MegaFlow Filter Cartridges
編號：
Parker’s Fulflo? MegaFlow? cartridges
provide a cost effective alternative
to wound and other 2 1/2 inch OD style
filter cartridges in high flow applications
such as reverse osmosis pre-filtration.
provide a cost effective alternative
to wound and other 2 1/2 inch OD style
filter cartridges in high flow applications
such as reverse osmosis pre-filtration.
High Flow Capacity Pleated Filter Cartridges
Parker’s Fulflo? MegaFlow? cartridges
provide a cost effective alternative
to wound and other 2 1/2 inch OD style
filter cartridges in high flow applications
such as reverse osmosis pre-filtration
and similar applications where nominal
efficiency is sufficient. Each Mega-
FlowTM cartridge can handle flow rates
up to 175 gpm (662 lpm), significantly
reducing the number of cartridges
required and the housing size. Each 6
inch (152 mm) diameter MegaFlow?
cartridge has flow capacity equal to 8
standard 2 1/2 inch OD X 40 inch long
filter cartridges. Positive O-ring seals
and a built in handle make cartridge
installation reliable, fast and easy.
MegaFlow? cartridges are available in
either pleated polypropylene or cellulose
media with nominal ratings of 0.5,
1, 5 and 10 micron.
Benefits
? High flow capacity means fewer
cartridges and reduces labor costs to
change
? High flow capacity allows smaller
housings and less capital expenditure
? Built in handle makes change fast,
easy and safe
? O -ring seal assures filtration integrity
? C hoice of polypropylene or cellulose
media allows use in both aqueous
and non-aqueous fluid applications
? T hermally bonded polypropylene and
phenolic resin bonded cellulose filter
media prevent particle bleed through
and unloading that commonly occurs
with wound cartridges
? High surface area pleated design
provides lower pressure drop
and longer service life than other
cartridges
? All materials of construction in
polypropylene cartridges comply with
FDA regulations per CFR Title 21
? Horizontal and vertical housings are
available for flow rates up to 3,325
gpm (12,586 LPM)
Applications
? Potable Water
? W aste Water
? R everse Osmosis Pre-Filtration
? Lubricating Oil
? Coolants
Specifications
Materials of Construction:
Media: Polypropylene microfiber (P
Code); Cellulose with phenolic binder
(C Code)
Support Layers: Polypropylene (P Code);
None (C Code)
End caps: Glass Filled Polypropylene
O-Rings: Buna-N, EPR, Silicone,
Fluoroelastomer
Recommended Operating Conditions:
Change Out Differential Pressure:
35 psid (2.4 bar)
Maximum Flow Rate: 175 gpm (662 lpm)
Maximum Temperature: 200°F (93°C)
Maximum Differential Pressure: 150 psid
(10 bar)
Nominal Filtration Ratings:
(90%) 0.5, 1, 5 and 10 μm
Dimensions:
6 in (152 mm) OD, 3.5 in (89 mm) ID,
40 in (1016 mm) long
Surface Area:
55-60 ft2 (5.1-5.6m2)
Flow Rate and Pressure Drop Formulas
Flow Rate (gpm) = C lean DP x Length Factor
V iscosity x Flow Factor
Clean DP = Flow Rate x Viscosity x Flow Factor
Length Factor
1. Clean DP is PSI differential at start.
2. Viscosity is centistokes. Use Conversion Tables
for other units.
3. Flow Factor is DP/GPM at 1 cks for 10 in
(or single).
4. Length Factors convert flow or DP from 10 in
(single length) to required cartridge length.
